CB型橡胶止水带价格
是指中间有孔的中埋式止水带，可分为cb型橡胶止水带、cb型塑料止水带两类。主要适用于各种混凝土构筑物的伸缩缝、沉降缝及防震缝等，具有与混凝土锚固紧密、止水密封和适应变形缝伸缩变形的能力优秀等
It refers to the middle burial water stop belt in the middle, which can be divided into two types: CB type rubber sealing belt and CB type plastic water stop belt. It is mainly applied to expansion joints, settlement joints and earthquake proof joints of all kinds of concrete structures. It has excellent ability to closely anchor with concrete, to seal water and seal, and to adapt to deformation and joint expansion and deformation.
特点，是我公司根据多年生产经验，并结合《给水排水工程混凝土构筑物变形缝设计规程》cecs117：2000开发生产的一种新型中埋式止水带.
The characteristic is our company based on many years of production experience and combined with the "design specification for deformation joint design of water and drainage engineering concrete structure" cecs117:2000, a new type of buried watertight belt.
设计及选用标准：
Design and selection criteria:
在工程设计及施工选用过程中，cb型止水带的宽度及厚度应按以下条件确定
In the process of engineering design and construction selection, the width and thickness of the CB type water stop belt should be determined according to the following conditions
CB型橡胶止水带价格
1、 水压小于4m,水平和垂直变形量不超过10mm 时，止水带的宽度不宜小于200mm，厚度不宜小于5mm；
1, when the water pressure is less than 4m and the horizontal and vertical deformation is not more than 10mm, the width of the water stop belt should not be less than 200mm, and the thickness should not be less than 5mm.
2、 水压为4-8m，水平和垂直变形量不超过30mm时，cb型止水带的宽度不宜小于300mm，厚度不宜小于6mm；
2. When the water pressure is 4-8M and the horizontal and vertical deformation is not more than 30mm, the width of the CB type water stop belt should not be less than 300mm, and the thickness should not be less than 6mm.
3、 水压大于8m,水平和垂直变形量超过30mm时，cb型止水带的宽度不宜小于350mm ,厚度不宜小于8mm；
3, when the water pressure is more than 8m and the horizontal and vertical deformation exceeds 30mm, the width of the CB type water stop belt should not be less than 350mm, and the thickness should not be less than 8mm.
4、 水压不大于8m,水平变形量不超过20mm，当无垂直变形时，cb型止水带的宽度不宜小于200mm,厚度不宜小于5mm。
4, the water pressure is not more than 8m, and the horizontal deformation is not more than 20mm. When there is no vertical deformation, the width of the CB type water stop belt should not be less than 200mm, and the thickness should not be less than 5mm.
除此之外，当结构断面尺寸大于500mm时，cb型止水带的宽度不宜小于300mm，当cb型止水带进行弯曲放置时，其转弯半径不得小于300mm。
Besides, when the structural section size is larger than 500mm, the width of the CB type water stop should not be less than 300mm. When the CB type water stop belt is bent, the turning radius should not be less than 300mm.